◆Coateau
Window Tint · 5 min read

Window Tint Spec Sheets Explained: Comparing Films Across Brands

Published November 19, 2026 · By the Coateau editorial team

To compare window tint films across brands, line up the same shade and read three columns: visible light transmission (VLT), total solar energy rejected (TSER) and the infrared number, then check which test glass and method each sheet used. That last step matters more than most buyers realize: XPEL tests on 3mm glass with EN 410 methods, while LLumar and SunTek report on 6mm glass under NFRC guidelines, so their figures are not on the same scale.

This guide walks through each column you will find on a real spec sheet, using published data from XPEL, LLumar and SunTek, and shows which numbers are safe to compare and which are not. For why TSER is the best single predictor of cabin comfort, see the ceramic tint heat rejection explainer; this page is about reading the sheet itself.

What would window tint cost on your car?

Instant price range for your exact vehicle, then offers from studios near you. Free, no account needed.

Get my price →

The columns, one by one

Spec sheets look dense, but most use the same handful of measurements. Once you know what each one describes, you can ignore the columns that do not separate one film from another and focus on the ones that do.

Common window film spec sheet columns
ColumnWhat it measuresWhat to do with it
VLT (visible light transmission)Share of visible light that passes through film and glassMatch to your state's legal limit
VLR (visible light reflectance)Share of visible light reflectedCheck against state reflectance caps
TSER (total solar energy rejected)UV, visible and infrared energy kept out, combinedBest single number for heat comparison
IRERInfrared rejection from 780 to 2500nm, including absorbed and re-radiated heatFair cross-brand IR comparison
SIRR (selective IR rejection)Infrared from 780 to 2500nm not directly transmittedHigher than IRER; compare only with other SIRR figures
IR rejection at 1025nmInfrared blocked at one wavelengthMarketing headline; do not compare with SIRR or IRER
UV rejectionUltraviolet blocked, often 300 to 380nmShould be 99% on any quality film
Glare reductionReduction in visible glare compared with bare glassTracks closely with darkness
Shading coefficientHeat gain compared with clear glass; lower is betterUseful within one brand's sheet

Why the test glass changes the numbers

Glass absorbs some solar energy on its own, and thicker glass absorbs more. That is why the footnotes matter. XPEL's PRIME spec sheet (revision R0523, the version quoted throughout this page) says all values are measured with film applied to 1/8 inch (3mm) glass plates on a spectrophotometer, using EN 410 methodology for visible and solar data. LLumar's and SunTek's sheets say their data follow National Fenestration Rating Council guidelines on single-pane 1/4 inch (6mm) clear glass.

Different glass and different standards mean a TSER of 59% on one sheet and 54% on another may not reflect a 5-point real-world gap. Both LLumar and SunTek also note that actual performance varies with glass type and properties. Use cross-brand comparisons to sort films into tiers, then let installer quality and warranty break close calls.

Compare films within one sheet freely. Compare across sheets only after reading the footnotes.

The infrared number is where marketing lives

Infrared rejection is the column most often quoted in ads, and it is measured three different ways. XPEL's headline IR rejection is taken at a single wavelength, 1025nm. The same sheet also lists IRER across 780 to 2500nm, which it describes as accounting for absorbed and re-radiated infrared. LLumar and SunTek publish SIRR, infrared not directly transmitted over 780 to 2500nm, plus IRER.

The gaps can be large. On XPEL's R0523 sheet, PRIME XR PLUS 35 lists 96% IR rejection at 1025nm, 70% IRER and 59% TSER; XPEL's newer R062526 data sheet gives XR PLUS as ranges across shades, 92% to 96% at 1025nm, 67% to 70% IRER and 52% to 71% TSER. LLumar IRX 35 lists 87% SIRR, 60% IRER and 54% TSER. SunTek Evolve 35 lists 93% SIRR, 64% IRER and 57% TSER. Read side by side, the single-wavelength and SIRR numbers make the films look further apart, or closer together, than the IRER and TSER figures suggest.

About 35% shades from three published spec sheets (XPEL rows from PRIME sheet R0523)
FilmVLTTSERHeadline IRIRERTest basis
XPEL PRIME XR PLUS 3538%59%96% at 1025nm70%3mm glass, EN 410
XPEL PRIME XR Black 3536%59%78% at 1025nm58%3mm glass, EN 410
LLumar IRX 3539%54%87% SIRR60%6mm glass, NFRC
SunTek Evolve 3538%57%93% SIRR64%6mm glass, NFRC
LLumar CTX 3537%48%69% SIRR48%6mm glass, NFRC
SunTek CXP 35 Black33%53%79% SIRR55%6mm glass, NFRC

VLT on the sheet is not VLT on your car

Spec sheet VLT is measured on clear test glass. Your car's side glass is rarely perfectly clear, and a tint meter reads film and glass together, so the installed reading is usually a few points darker than the label. A film sold as 35% can read in the low 30s or below once applied, which matters in a state with a 35% front-window limit. The guide to how window tint is measured covers meters and legal tolerances.

Also notice that the shade name and the measured VLT often differ. On XPEL's sheet, XR PLUS 35 lists 38% VLT and XR PLUS 15 lists 12%. On SunTek's, CXP 35 Black lists 33%. Use the VLT column, not the product name, when you check a film against your state limit.

The secondary columns: reflectance, absorbance and shading coefficient

Reflectance (VLR) is the share of visible light the film bounces back, and it matters for two reasons: state reflectance caps and looks. Most non-metallic films sit in single digits. On XPEL's sheet, XR PLUS 35 lists 7% VLR; on LLumar's, IRX 35 lists 6% visible light reflection. Metallized films run higher, which is where reflectance caps come into play.

XPEL also breaks solar energy into transmittance, reflectance and absorbance. Non-metallic films stop energy mainly by absorbing it rather than reflecting it: XR PLUS 35 lists 74% solar absorbance against 6% solar reflectance. Absorbed heat is partly re-radiated into the cabin, which is why IRER, a measure that accounts for absorbed and re-radiated infrared, is a more honest number than a single-wavelength IR figure. The shading coefficient column compares heat gain with clear glass, and lower is better. On XPEL's sheet it falls from 0.73 for CS Black 35 to 0.47 for XR PLUS 35, a useful within-brand check that tracks the TSER column.

None of these columns should decide a purchase by themselves. Use them to confirm what TSER and IRER already tell you, and to rule out films that would break a reflectance limit in your state.

A short checklist before you pick a film

Ask the shop for the manufacturer's current spec sheet for the exact film and shade they are quoting, not a brochure. Then work through it in order, and only bring price into it once the films are sorted into tiers.

  • ◆Confirm the VLT column fits your state limit, allowing a few points for your glass
  • ◆Compare TSER first, within one brand's sheet if possible
  • ◆Compare IRER rather than single-wavelength IR when crossing brands
  • ◆Check reflectance against your state's cap if you are considering metallic film
  • ◆Read the footnotes for glass thickness, standard and tolerance
  • ◆Confirm the warranty terms and whether the shop registers them
What would window tint cost on your car?

Instant price range for your exact vehicle, then offers from studios near you. Free, no account needed.

Get my price →

Frequently asked questions

What is the most important number on a tint spec sheet?

For heat, TSER, because it counts UV, visible light and infrared together. For legality, VLT. Use the IR figure only after checking how it was measured.

Why does XPEL's IR rejection look higher than other brands?

XPEL's headline figure is measured at a single 1025nm wavelength. Its IRER figure across 780 to 2500nm is lower and is the fairer number to compare with other brands' IRER.

Can I compare TSER between XPEL and LLumar?

Roughly. XPEL tests on 3mm glass with EN 410 methods and LLumar on 6mm glass under NFRC guidelines, so treat small gaps of a few points as noise.

Why does my tint meter read darker than the spec sheet?

The sheet measures film on clear test glass. A meter reads your car's glass plus the film, and most car glass is not perfectly clear.

Sources