---
title: "Window Tint Spec Sheets Explained: Comparing Films Across Brands"
description: "How to read a tint spec sheet column by column, and why XPEL's numbers cannot be compared line for line with LLumar's or SunTek's."
type: guide
service: window-tint
publishAt: "2026-11-19T00:31:08.000Z"
canonical: "https://coateau.com/guides/window-tint-spec-sheet-explained"
sources:
  - label: "XPEL PRIME USA specification sheet (R0523): test method, 1025nm IR, IRER and tolerance"
    url: "https://www.xpel.com/web-assets/downloads/XPEL_PRIME_spec_sheet_USA_Rev0523.pdf"
  - label: "LLumar automotive window film performance data (NFRC, 6mm glass)"
    url: "https://llumar.com/content/dam/eastman/performance-films/llumar/nar/documents/english/auto/llumar-automotive-window-film-performance-data.pdf"
  - label: "SunTek automotive window film specifications (NFRC, 6mm glass)"
    url: "https://suntekfilms.com/content/dam/eastman/performance-films/suntek-films/documents/film-specifications/automotive-window-film-specifications.pdf"
  - label: "XPEL Prime XR Plus technical data sheet (R062526)"
    url: "https://assets.contentstack.io/v3/assets/blt4d9a5b94323eb907/blt09822e5b6f0b92f5/6a579e9fd1c6417559e054dd/XPEL_PRIME_XR_Plus_TDS_New_R062526.pdf"
---

# Window Tint Spec Sheets Explained: Comparing Films Across Brands

To compare window tint films across brands, line up the same shade and read three columns: visible light transmission (VLT), total solar energy rejected (TSER) and the infrared number, then check which test glass and method each sheet used. That last step matters more than most buyers realize: XPEL tests on 3mm glass with EN 410 methods, while LLumar and SunTek report on 6mm glass under NFRC guidelines, so their figures are not on the same scale.

This guide walks through each column you will find on a real spec sheet, using published data from XPEL, LLumar and SunTek, and shows which numbers are safe to compare and which are not. For why TSER is the best single predictor of cabin comfort, see the ceramic tint heat rejection explainer; this page is about reading the sheet itself.

## Key facts

- **LLumar and SunTek report on single-pane 6mm (1/4 inch) clear glass using NFRC guidelines**; XPEL reports on 3mm (1/8 inch) glass using EN 410 methodology.
- **XPEL's headline IR rejection is measured at one wavelength, 1025nm**; LLumar and SunTek publish SIRR and IRER across 780 to 2500nm instead.
- **XPEL PRIME XR PLUS 35 lists 96% IR rejection at 1025nm but 70% IRER and 59% TSER** on XPEL's PRIME spec sheet revision R0523.
- **XPEL states a tolerance of plus or minus 3%** on its visible light, solar energy, UV and IR values.
- **UV rejection is a poor way to choose between quality films**: every PRIME, CTX, IRX and ATC row lists 99% or more.

## The columns, one by one

Spec sheets look dense, but most use the same handful of measurements. Once you know what each one describes, you can ignore the columns that do not separate one film from another and focus on the ones that do.

_Common window film spec sheet columns_

| Column | What it measures | What to do with it |
| --- | --- | --- |
| VLT (visible light transmission) | Share of visible light that passes through film and glass | Match to your state's legal limit |
| VLR (visible light reflectance) | Share of visible light reflected | Check against state reflectance caps |
| TSER (total solar energy rejected) | UV, visible and infrared energy kept out, combined | Best single number for heat comparison |
| IRER | Infrared rejection from 780 to 2500nm, including absorbed and re-radiated heat | Fair cross-brand IR comparison |
| SIRR (selective IR rejection) | Infrared from 780 to 2500nm not directly transmitted | Higher than IRER; compare only with other SIRR figures |
| IR rejection at 1025nm | Infrared blocked at one wavelength | Marketing headline; do not compare with SIRR or IRER |
| UV rejection | Ultraviolet blocked, often 300 to 380nm | Should be 99% on any quality film |
| Glare reduction | Reduction in visible glare compared with bare glass | Tracks closely with darkness |
| Shading coefficient | Heat gain compared with clear glass; lower is better | Useful within one brand's sheet |

## Why the test glass changes the numbers

Glass absorbs some solar energy on its own, and thicker glass absorbs more. That is why the footnotes matter. XPEL's PRIME spec sheet (revision R0523, the version quoted throughout this page) says all values are measured with film applied to 1/8 inch (3mm) glass plates on a spectrophotometer, using EN 410 methodology for visible and solar data. LLumar's and SunTek's sheets say their data follow National Fenestration Rating Council guidelines on single-pane 1/4 inch (6mm) clear glass.

Different glass and different standards mean a TSER of 59% on one sheet and 54% on another may not reflect a 5-point real-world gap. Both LLumar and SunTek also note that actual performance varies with glass type and properties. Use cross-brand comparisons to sort films into tiers, then let installer quality and warranty break close calls.

> Compare films within one sheet freely. Compare across sheets only after reading the footnotes.

## The infrared number is where marketing lives

Infrared rejection is the column most often quoted in ads, and it is measured three different ways. XPEL's headline IR rejection is taken at a single wavelength, 1025nm. The same sheet also lists IRER across 780 to 2500nm, which it describes as accounting for absorbed and re-radiated infrared. LLumar and SunTek publish SIRR, infrared not directly transmitted over 780 to 2500nm, plus IRER.

The gaps can be large. On XPEL's R0523 sheet, PRIME XR PLUS 35 lists 96% IR rejection at 1025nm, 70% IRER and 59% TSER; XPEL's newer R062526 data sheet gives XR PLUS as ranges across shades, 92% to 96% at 1025nm, 67% to 70% IRER and 52% to 71% TSER. LLumar IRX 35 lists 87% SIRR, 60% IRER and 54% TSER. SunTek Evolve 35 lists 93% SIRR, 64% IRER and 57% TSER. Read side by side, the single-wavelength and SIRR numbers make the films look further apart, or closer together, than the IRER and TSER figures suggest.

_About 35% shades from three published spec sheets (XPEL rows from PRIME sheet R0523)_

| Film | VLT | TSER | Headline IR | IRER | Test basis |
| --- | --- | --- | --- | --- | --- |
| XPEL PRIME XR PLUS 35 | 38% | 59% | 96% at 1025nm | 70% | 3mm glass, EN 410 |
| XPEL PRIME XR Black 35 | 36% | 59% | 78% at 1025nm | 58% | 3mm glass, EN 410 |
| LLumar IRX 35 | 39% | 54% | 87% SIRR | 60% | 6mm glass, NFRC |
| SunTek Evolve 35 | 38% | 57% | 93% SIRR | 64% | 6mm glass, NFRC |
| LLumar CTX 35 | 37% | 48% | 69% SIRR | 48% | 6mm glass, NFRC |
| SunTek CXP 35 Black | 33% | 53% | 79% SIRR | 55% | 6mm glass, NFRC |

## VLT on the sheet is not VLT on your car

Spec sheet VLT is measured on clear test glass. Your car's side glass is rarely perfectly clear, and a tint meter reads film and glass together, so the installed reading is usually a few points darker than the label. A film sold as 35% can read in the low 30s or below once applied, which matters in a state with a 35% front-window limit. The guide to how window tint is measured covers meters and legal tolerances.

Also notice that the shade name and the measured VLT often differ. On XPEL's sheet, XR PLUS 35 lists 38% VLT and XR PLUS 15 lists 12%. On SunTek's, CXP 35 Black lists 33%. Use the VLT column, not the product name, when you check a film against your state limit.

## The secondary columns: reflectance, absorbance and shading coefficient

Reflectance (VLR) is the share of visible light the film bounces back, and it matters for two reasons: state reflectance caps and looks. Most non-metallic films sit in single digits. On XPEL's sheet, XR PLUS 35 lists 7% VLR; on LLumar's, IRX 35 lists 6% visible light reflection. Metallized films run higher, which is where reflectance caps come into play.

XPEL also breaks solar energy into transmittance, reflectance and absorbance. Non-metallic films stop energy mainly by absorbing it rather than reflecting it: XR PLUS 35 lists 74% solar absorbance against 6% solar reflectance. Absorbed heat is partly re-radiated into the cabin, which is why IRER, a measure that accounts for absorbed and re-radiated infrared, is a more honest number than a single-wavelength IR figure. The shading coefficient column compares heat gain with clear glass, and lower is better. On XPEL's sheet it falls from 0.73 for CS Black 35 to 0.47 for XR PLUS 35, a useful within-brand check that tracks the TSER column.

None of these columns should decide a purchase by themselves. Use them to confirm what TSER and IRER already tell you, and to rule out films that would break a reflectance limit in your state.

## A short checklist before you pick a film

Ask the shop for the manufacturer's current spec sheet for the exact film and shade they are quoting, not a brochure. Then work through it in order, and only bring price into it once the films are sorted into tiers.

- Confirm the VLT column fits your state limit, allowing a few points for your glass
- Compare TSER first, within one brand's sheet if possible
- Compare IRER rather than single-wavelength IR when crossing brands
- Check reflectance against your state's cap if you are considering metallic film
- Read the footnotes for glass thickness, standard and tolerance
- Confirm the warranty terms and whether the shop registers them

## Frequently asked questions

**Q: What is the most important number on a tint spec sheet?**
A: For heat, TSER, because it counts UV, visible light and infrared together. For legality, VLT. Use the IR figure only after checking how it was measured.

**Q: Why does XPEL's IR rejection look higher than other brands?**
A: XPEL's headline figure is measured at a single 1025nm wavelength. Its IRER figure across 780 to 2500nm is lower and is the fairer number to compare with other brands' IRER.

**Q: Can I compare TSER between XPEL and LLumar?**
A: Roughly. XPEL tests on 3mm glass with EN 410 methods and LLumar on 6mm glass under NFRC guidelines, so treat small gaps of a few points as noise.

**Q: Why does my tint meter read darker than the spec sheet?**
A: The sheet measures film on clear test glass. A meter reads your car's glass plus the film, and most car glass is not perfectly clear.

## Sources

- [XPEL PRIME USA specification sheet (R0523): test method, 1025nm IR, IRER and tolerance](https://www.xpel.com/web-assets/downloads/XPEL_PRIME_spec_sheet_USA_Rev0523.pdf)
- [LLumar automotive window film performance data (NFRC, 6mm glass)](https://llumar.com/content/dam/eastman/performance-films/llumar/nar/documents/english/auto/llumar-automotive-window-film-performance-data.pdf)
- [SunTek automotive window film specifications (NFRC, 6mm glass)](https://suntekfilms.com/content/dam/eastman/performance-films/suntek-films/documents/film-specifications/automotive-window-film-specifications.pdf)
- [XPEL Prime XR Plus technical data sheet (R062526)](https://assets.contentstack.io/v3/assets/blt4d9a5b94323eb907/blt09822e5b6f0b92f5/6a579e9fd1c6417559e054dd/XPEL_PRIME_XR_Plus_TDS_New_R062526.pdf)
